1.rc servo motor with position feedback
2.Standard digital metal gears servo 2BB
3.servo torque can add feedback :3KG/6KG/9KG/15KG/21KG
4.Constant current protection
Feetech FB5116M 16kg Digital Servo 4 pin wire Position Feedback Servo
Feature:
1.15kg Metal Gear Digital feedback Servo
2.large angle 300 degree
3.Apply for robot project
4.Constant current protection
Advantage:
- Large Angle control (300 degrees: 500-2500us)
-Out of control protection (off the signal and unable to output)
-Overheating protection (over 80 ºC to output, programmable adjusting)
-Overload protection (over 80% of the torque of the blocking torque, lasting for 8 seconds, the torque becomes smaller)
-High servo update rate (250Hz)
-Dual-mode operation (programmable switch between servo mode and motor mode)
SKU:FB5116M
Dead band: 2μ 1500μs / 330hz
Operating Speed (4.8V): 0.25sec/60°
Operating Speed (6V): 0.2 sec/60°
Stall Torque (6V): 13 kg.cm (180.85 oz/in)
Stall Torque (7.4V): 15.5 kg-cm (215.6 oz/in)
Dimensions: 40X20.1X38.3mm /1.59 X0.80X49 in
Weight: 64 g
Connector Wire Length: JR 265 mm (10.43in)
Bearing: 2BB
Specifications:
| No. | Item | Specification |
| 3-1 | Size | A:40mm B:20.1mm C:38.3mm D:54mm |
| 3-2 | Weight | 64g |
| 3-3 | Gear type | Copper Gear |
| 3-6 | Limit angle | No limit |
| 3-7 | Bearing | 2 Ball bearings |
| 3-8 | Horn gear spline | 25T(5.9mm) |
| 3-9 | Horn type | Plastic,POM |
| 3-10 | Case | Nylon & Fiberglass |
| 3-11 | Connector wire | 300mm ±5 mm(Brown ,Red and Yellow) |
| 3-12 | Motor | Metal brush motor |
| 3-13 | Splash water resistance | NO |
| 4.Electrical Specification (Function of the Performance) |
| | | | |
| 4-1* | Idle current(at stopped) | 5mA | 7mA |
| 4-2* | No load speed | 0.25sec/60° | 0.2 sec/60° |
| 4-3* | Runnig current(at no load) | 130 mA | 150 mA |
| 4-4 | Peak stall torque | 13kg.cm | 15.5kg.cm |
| 180.85oz.in | 215.6oz.in |
| 4-5 | Stall current | 1500 mA | 1800mA |
Feature:
1: Large angle control (300 degrees: 500-2500us)
2: With out-of-control protection (out-of-signal unable to output)
3: Overheat protection (unable to output when exceeding a certain temperature, temperature control degree can be set in the range of 10-80 degrees according to the customer's needs when leaving the factory)
4: Overload protection (over 80% of blocking torque, lasts for 8 seconds, and the torque decreases)
5: High Servo Update Rate (250Hz)
6: Dual-mode operation (programmable switching servo mode and motor mode)
7: With analog feedback (0.1V-3.2V corresponds to 0-300 degrees)
Mechanical Specification |
Item | Specification |
Size | A:40mm B:20.1mm C:38.3mm D:54mm |
Weight | 64g |
Gear type | Copper Gear |
Limit angle | No limit |
Bearing | 2 Ball bearings |
Horn gear spline | 25T(5.9mm) |
Horn type | Plastic,POM |
Case | Nylon & Fiberglass |
Connector wire | 300mm ±5 mm(Black ,Red,white and Yellow) |
Motor | Metal brush motor |
Splash water resistance | NO |
Electrical Specification (Function of the Performance) |
Operating Voltage Range | 4.8V | 6V |
Idle current(at stopped) | 5mA | 7mA |
No load speed | 0.25sec/60° | 0.2 sec/60° |
Runnig current(at no load) | 130 mA | 150 mA |
Peak stall torque | 13kg.cm | 15.5kg.cm |
Stall current | 1500 mA | 1800mA |
Servo Picture:
Feature:
1.360 Degree Continuous Rotation Servo
2.standard metal gears servo 2BB
3.Programmable servo
4.two working mode
Specification:
SKU:FB5317M
Dead band: 2μ 1500μs / 330hz
Operating Speed (4.8V): 0.18 sec/60°
Operating Speed (6V): 0.16 sec/60°
Stall Torque (4.8V): 15 kg.cm (197.93 oz/in)
Stall Torque (6V): 17 kg-cm (212.79 oz/in)
Dimensions: 40.5X20.2X38mm /1.59 X0.80X49 in
Weight: 55.6 g (1.96oz)
Connector Wire Length: 265 mm (10.43in)
Bearing: 2BB
Features
-Standard digital programmable Metal gears servo,2BBw
-High quality core motor, no limits can 360 degree rotation
-Two working mode (servo mode and 360 degree continue rotation mode)
-Operating Voltage: 4.8V-8.4V
-Dead band width: 2usc
-Interface: (like JR)
-Wire length: 30cm
This Stand Size form Feetech servo Factroy with 360 degree continuous rotation is compatible with servo
shields for Arduino.
It's a very versatile servo motor for micro robots or other
applications where you don't have much space and the need of a full
rotational motor with the benefits of a servo. This servo is capable of
full 360 degree continuous rotation and can be connected to an output pin of
an Arduino board directly without the need of a motor driver.
Programming the rotation in the Arduino IDE is as easy as the programming of the servo movement.
With the included servo library from the Arduino website you can just make the servo
rotating clockwise, counterclockwise or stop by writing the related servo angels.
Servo programmable function
1. FAIL SAFE, On or Off
2. Direction of Rotation
3. Travel Speed
4. Servo Max Torque limit, and Punch
5. Center, End, and FAIL SAFE Point
6. Signal Pulse Set-Up
7. Stretch (Holding Power, Running Power, Acceleration and Deceleration)
8. Dead Band Width
9. Resolution Setup
10."Save and Open" File Options
11. Reset Factory Default Data
12.Read and Write Servo Data
Specification:
Company Information
our servos is very competitive and sell well on the market this year.We have some new products online now,I am sure you could make money on it.So introduce it for you
We mainly offer :
1,FITEC/FEETECH micro/small servo:2.5g,4.3g,5g,6g,7.5g,8g,9g,with ball bearing,9g ,9g with metal gear,9g metal gear digital servo,
2,FITEC/FEETECH standard servo:3kg.cm,6kg.cm,7kg.cm low profile digital servo,9kg.cm(Waterproof),13kg.cm(Waterproof),15kg.cm(Waterproof),17kg (Waterproof) 21kg (Waterproof) 25kg (Waterproof)
3,FITEC/FEETECH Titanium gear servo:
4,FITEC/FEETECH large torque servo:18kg.cm,20kg.cm,30kg.cm,40kg.cm rc servos.
-Standard digital Titanium gears servo,2BB
-Coreless motor,Aluminium middle hull
Our Services
There are 5 outstanding advantages of our servos, as follows,
1. The quality: our material has very good quality especially our 4 beginning servos----titanium gear, aluminum middle hull, dual ball bearing and so on. All our servos start producing after our servos get very good marks in testing. Recently, our company is producing an full metal case titanium gear digital servos with high spead which
which can be up to 0.06 sec/60.
2. The price: Our price are quite competitive whatever in China or in the world. If you have any interest in our servos, I will give you the price list.
3. The service: if there is wrong with the quality of servos, we will offer the replace defective items or replace a new one.
4. The appearance and package: they looks high-grade.
5. We have our own brand Feetech, but we can also do OEM and print your logo on servos as you need. Of course, the quantity must be a little higher! Which model do you interested to test on first time?
Service:
1."Reasonable price,delivery on time,good services" is our business principle
2.We have own factory,specialized in this field many years, warmly welcome your design
3.Small order and mixed items are available
4.Fast delivery as most of products we have in stock
5.Competetive price and good quality.
6.samples and products according to customers' requirement
